uksi/2018/352
uksi/2018/352 — The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018
Legal information, not legal advice. LEGALDIGM is not a law firm. Check the official source for the current text.
Analyze this law with AI2018 No. 352
Food, England
The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018
Made
7th March 2018
Laid before Parliament
12th March 2018
Coming into force
6th April 2018
The Secretary of State makes these Regulations in exercise of the powers conferred by sections 6(4), 16(1), 17(1), 26(1) and (3), 31 and 48(1) of the Food Safety Act 1990 now vested in relation to England in the Secretary of State .
The Secretary of State has had regard to relevant advice given by the Food Standards Agency in accordance with section 48(4A) of the Food Safety Act 1990 .
There has been consultation as required by Article 9 of Regulation (EC) No 178/2002 of the European Parliament and of the Council laying down the general principles and requirements of food law, establishing the European Food Safety Authority and laying down procedures in matters of food safety .
Citation, commencement and extent
1
1
These Regulations may be cited as the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) (Amendment) Regulations 2018 and come into force on 6th April 2018.
2
They extend to England and Wales.
Amendment of the Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007
2
The Natural Mineral Water, Spring Water and Bottled Drinking Water (England) Regulations 2007 are amended as follows.
Amendment of regulation 2 (interpretation)
3
In regulation 2(1)—
a
at the appropriate places insert the following definitions—
“pesticides” has the meaning given in note 6 of Part B of Annex 1 to Council Directive 98/83/EC on the quality of water for human consumption ;
;
“polycyclic aromatic hydrocarbons” means—
benzo(b)fluoranthene,
benzo(k)fluoranthene,
benzo(ghi)perylene, and
indeno(1,2,3-cd)pyrene;
;
“trihalomethanes” means—
chloroform,
bromoform,
dibromochloromethane, and
bromodichloromethane.
;
b
in the definition of “parameter”, for the words from “second column” to the end substitute “first column of any table in Schedule 2 or the first column of the table in Section 1 of Part 9 of Schedule 12”;
c
omit the definition of “prescribed concentration or value”;
d
at the end of the definition of “relevant authority” omit “and”.
Amendment of regulation 3 (exemptions)
4
For regulation 3(1)(a) substitute—
a
is a medicinal product within the meaning of Directive 2001/83/EC of the European Parliament and of the Council on the Community code relating to medicinal products for human use ;
.
Amendment of regulation 14 (marking, labelling and advertising of bottled drinking water)
5
In regulation 14, in paragraphs (a) and (b), in the words before sub-paragraph (i), omit the words from “which” to “Annex I”.
Amendment of regulation 16 (enforcement)
6
1
Regulation 16 is amended as follows.
2
In paragraph (5)—
a
in sub-paragraph (a)—
i
in the words before paragraph (i), for “to check” substitute “, including checks to determine”;
ii
in paragraph (i), at the end insert “and”;
iii
omit paragraphs (ii) to (iv);
b
omit sub-paragraphs (b) to (d).
3
In paragraph (6), omit “, (b) and (d)”.
Insertion of regulation 16A (monitoring of bottled spring water and bottled drinking water)
7
After regulation 16, insert—
Monitoring of water bottled and labelled as “spring water” and bottled drinking water
16A
Each food authority must, in accordance with Schedule 12, maintain a monitoring programme for, and monitor, any water that—
a
is water to which paragraph 3 of Schedule 12 applies (water bottled and labelled as “spring water” and bottled drinking water), and
b
is being bottled in its area.
.
Omission of regulations 19 to 21 (methods of analysis, offences and penalties and defences)
8
Omit—
a
regulation 19 (methods of analysis);
b
regulation 20 (offences and penalties);
c
regulation 21 (defences).
Substitution of regulation 22 (application of provisions of the Food Safety Act 1990)
9
For regulation 22 substitute—
Application of the Act
22
1
The provisions of the Act specified in the first column of the table in Schedule 13 apply for the purposes of these Regulations, with the modifications specified in the second column of that table.
2
An authorised officer of a food authority must not serve an improvement notice under section 10(1) of the Act, as applied and modified by paragraph (1), as read with Schedule 13, if—
a
the improvement notice would relate to water bottled and labelled before 6th April 2018, and
b
the matters constituting the alleged contravention would not have constituted an offence under these Regulations as they stood immediately before 6th April 2018.
.
Substitution of Schedule 2 (requirements for spring water and drinking water including prescribed concentrations or values of parameters)
10
For Schedule 2 (requirements for water bottled and labelled as “spring water” and bottled drinking water including concentration and value limits for microbiological, chemical and radioactive parameters) substitute the Schedule in Schedule 1.
Omission of Schedules 9 to 11 (audit monitoring, check monitoring and minimum sampling frequencies)
11
Omit—
a
Schedule 9 (properties, elements, substances and organisms, not being parameters, whose concentration or value in bottled drinking water and spring water must be determined by audit monitoring);
b
Schedule 10 (parameters, properties, elements, substances and organisms in relation to which check monitoring must be carried out);
c
Schedule 11 (minimum frequencies for sampling and analysis of spring water and bottled drinking water).
Insertion of Schedule 12 (monitoring provisions) and Schedule 13 (application of provisions of the Food Safety Act 1990)
12
At the appropriate places, insert the Schedules in Schedule 2 as Schedule 12 (monitoring of water bottled and labelled as “spring water” and bottled drinking water) and Schedule 13 (application and modification of provisions of the Food Safety Act 1990).
George Eustice
Minister of State
Department for Environment, Food and Rural Affairs
7th March 2018
SCHEDULE 1
New Schedule 2
Regulation 10
SCHEDULE 2
Requirements for water bottled and labelled as “spring water” and bottled drinking water
Regulations 10 and 13
PART 1
Requirements for water bottled and labelled as “spring water” and bottled drinking water
Water bottled and labelled as “spring water” and bottled drinking water meet the requirements of this Schedule if—
a
in relation to each of the parameters specified in the first column of the tables in Part 2 (microbiological parameters) and Part 3 (chemical parameters), it does not contain the parameter at a concentration or value exceeding the concentration or value specified for that parameter in the second column of the relevant table—
i
as measured by reference to the unit of measurement specified in the third column of the relevant table, and
ii
as read, in the case of the table in Part 3, with any further provision relating to the parameter, or concentration or value for the parameter, specified in the fourth column of the table,
b
in relation to each of the parameters specified in the first column of the table in Part 4 (radioactive substances), it does not contain the parameter at an activity concentration or value exceeding the activity concentration or value specified for that parameter in the second column of the relevant table as measured by reference to the unit of measurement specified in the third column of the table,
c
it does not contain (disregarding any parameters covered by sub-paragraphs (a) and (b)), any micro-organism, parasite or any other property, element or substance at a concentration or value that would constitute a potential danger to human health, and
d
it does not contain any substance (whether or not a parameter) at a concentration or value that, in conjunction with any other property, element, substance or organism it contains (whether or not a parameter), would constitute a potential danger to human health.
PART 2
Parametric values for microbiological parameters
Parameter Parametric value Unit of measurement
Escherichia coli
(E. coli)
0/250 ml number/250 ml Enterococci 0/250 ml number/250 ml Pseudomonas aeruginosa 0/250 ml number/250ml Colony count 22ºC 100/ml number/ml Colony count 37ºC 20/ml number/ml
PART 3
Parametric concentrations for chemical parameters
Parameter Parametric concentration Unit of measurement Further provision
Acrylamide 0.10 µg/l Antimony 5.0 µg Sb/l Arsenic 10 µg As/l Benzene 1.0 µg/l Benzo(a)pyrene 0.010 µg/l Boron 1.0 mg/l Bromate 10 µg/l BrO 3 /l Cadmium 5.0 µg Cd/l Chromium 50 µg Cr/l Copper 2.0 mg Cu/l Cyanide 50 µg CN/l 1,2-dichloroethane 3.0 µg/l Epichlorohydrin 0.10 µg/l Fluoride 1.5 mg F/l Lead 10 µg Pb/l Mercury 1.0 µg Hg/l Nickel 20 µg Ni/l Nitrate 50 mg NO 3/ l The concentration (mg/l) of nitrate divided by 50 added to the concentration (mg/l) of nitrite divided by 3 must not exceed 1. Nitrite 0.50 mg NO 2 /l The concentration (mg/l) of nitrate divided by 50 added to the concentration (mg/l) of nitrite divided by 3 must not exceed 1. Pesticides— Only those pesticides which are likely to be present in a given water must be monitored. (a) individual substances— (i) in the case of aldrin, dieldrin, heptachlor and heptachlor epoxide 0.030 µg/l The parametric concentration applies to each individual pesticide. (ii) in the case of other individual pesticides 0.10 µg/l The parametric concentration applies to each individual pesticide. (b) total pesticides 0.50 µg/l The concentration for “total pesticides” refers to the total sum of the concentrations of all the individual pesticides detected and quantified in the monitoring procedure. Polycyclic aromatic hydrocarbons 0.10 µg/l The parametric concentration applies to the total sum of the concentrations of all the individual polycyclic aromatic hydrocarbons detected and quantified in the monitoring procedure. Selenium 10 µg Se/l Tetrachloroethene and trichloroethene 10 µg/l The parametric concentration applies to the total sum of the concentrations of both of the parameters specified in the first column. Trichloromethanes 100 µg/l
The parametric concentration applies to the total sum of the concentrations of all the individual trichloromethanes
detected and quantified in the monitoring procedure.
Vinyl chloride 0.50 µg/l
PART 4
Parametric activity concentrations for radon and tritium and parametric value for indicative dose
Parameter Parametric activity concentration or value Unit of Measurement
Radon 100 Bq/l Tritium 100 Bq/l Indicative Dose 0.10 mSv
SCHEDULE 2
New Schedules 12 and 13
Regulation 12
SCHEDULE 12
Monitoring of water bottled and labelled as “spring water” and bottled drinking water
Regulation 16A
PART 1
Interpretation
General
1
In this Schedule—
“average” means mean average;
“the BSI” means the British Standards Institution;
“delegate” means a person to whom a task has been delegated by a food authority under paragraph 14, as read with paragraph 56, or a person to whom a food authority intends to delegate such a task (as the case may be);
“indicative dose” means the committed effective dose for one year of ingestion resulting from all the radionuclides (whether of natural or artificial origin) whose presence has been detected in a supply of water intended for human consumption but excluding potassium-40, radon, tritium and short-lived radon decay products;
“limit of quantification” has the meaning given in Article 2(2) of Commission Directive 2009/90/EC laying down, pursuant to Directive 2000/60/EC of the European Parliament and of the Council, technical specifications for chemical analysis and monitoring of water status ;
“paragraph 45 determination” means a determination under paragraph 45 relating to indicative dose”;
“parametric concentration”, in relation to a parameter specified in the first column of the table in Part 3 of Schedule 2 or a parameter specified in the first column of the table in Section 1 of Part 9 for which a maximum concentration (as opposed to a value) is set, means the maximum concentration given for the parameter in the second column of the relevant table, as measured by reference to the unit of measurement specified in the third column of the relevant table;
“radioactive substance” has the meaning given in Article 2(2) of Council Directive 2013/51/Euratom laying down requirements for the protection of the health of the general public with regard to radioactive substances in water intended for human consumption ;
“Regulation 882/2004” means Regulation (EC) No 882/2004 of the European Parliament and of the Council on official controls performed to ensure the verification of compliance with feed and food law, animal health and animal welfare rules ;
“sample” means a sample taken under this Schedule;
“trueness” (the systematic error) means the difference between the mean value of the large number of repeated measurements and the true value, as further described in ISO 5725-1:1994(en) entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions” published by the International Organization for Standardization on 22nd December 1994, as amended by ISO 5725-1:1994/Cor 1:1998 entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions TECHNICAL CORRIGENDUM 1” published by the International Organization for Standardization on 2nd May 1998;
“uncertainty of measurement” means a non-negative parameter characterising the dispersion of the quantity values being attributed to a measure based on the information used;
“year” means, unless a contrary intention appears, a calendar year or such other 12 month period as a food authority may, from time to time, decide to use for the purpose of its monitoring programme.
Delegated tasks
2
Where a food authority has entered into an arrangement with a person under paragraph 14, as read with Part 10, for a delegate to carry out a task specified in the first column of the table in Section 2 of Part 10 on its behalf, any reference to a food authority in that provision, and in any related provision in this Schedule, is to be read as a reference to the delegate for the purpose of carrying out that task during the duration of the delegation arrangement.
PART 2
General
Application
3
This Schedule applies to the monitoring of—
a
water that is bottled and labelled as “spring water” by a food business in the course of its business as a bottler of water, whether the bottling of water is its main business or part of its business, and
b
drinking water that is bottled by a food business in the course of its business as a bottler of water, whether the bottling of water is its main business or part of its business.
Sampling: general
4
1
For the purpose of carrying out its obligations under the provisions specified in sub-paragraph (2), each food authority must take and analyse samples of any water bottled in its area to which this Schedule applies.
2
The provisions are—
a
paragraph 7(1) (microbiological parameters);
b
paragraph 8(1) (chemical parameters);
c
paragraph 9, as read with paragraphs 23 and 25(1) (radon);
d
paragraph 10, as read with paragraphs 29 and 31(1) (tritium);
e
paragraph 11 (indicative dose), as read with—
i
paragraph 38(2), where a decision is taken by the food authority under paragraph 38(1) to screen water by determining its gross alpha activity to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;
ii
paragraph 39(2), where a decision is taken by the food authority under paragraph 39(1) to screen water by determining its gross beta activity to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;
iii
paragraph 40(2), where a decision is taken by the food authority under paragraph 40(1) to screen water by analysing one radionuclide to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;
iv
paragraph 41(2), where a decision is taken by the food authority under paragraph 41(1) to screen water by analysing more than one radionuclide to determine whether it is necessary for the authority to carry out a paragraph 45 determination for the water;
v
paragraph 43(1) (determination relating to the presence and concentration of radionuclides);
f
paragraph 12, as read with paragraph 50(1) (indicator parameters);
g
paragraph 13 (other parameters not mentioned in this sub-paragraph).
3
For the purpose of its sampling obligations under this Schedule, a food authority must take samples of water at the point at which the water is put into a bottle.
Sampling: non-radioactive substances
5
1
In the case of samples of water that a food authority must take and analyse to enable it to discharge its obligations under the provisions specified in paragraph 4(2)(a) (b), (f) and (g), each food authority must take and analyse such samples regularly, having regard to the provisions contained in—
a
Article 17(2) of Regulation (EC) No 178/2002 of the European Parliament and of the Council laying down the general principles and requirements of food law, establishing the European Food Safety Authority and laying down procedures in matters of food safety (monitoring responsibilities), and
b
Article 3(1) of Regulation 882/2004 (obligation to carry out official controls regularly, on a risk basis and with appropriate frequency so as to achieve the objectives of Regulation 882/2004).
2
Where, under sub-paragraph (1), a food authority only takes one sample in a year of any water in its area to which this Schedule applies, the authority must take the samples from year to year at intervals that are spread out in such a way—
a
to avoid the results, when considered together, giving a potentially distorted picture of the state of the water because the samples have been taken too closely together in time, and
b
so that the results, when considered together, provide information about the water that is representative of the quality of the water during the relevant years.
3
Where, under sub-paragraph (1), a food authority takes more than one sample in a year of any water in its area to which this Schedule applies, the authority must take the samples at intervals that are spread out throughout the year in such a way—
a
to avoid the results, when considered together, giving a potentially distorted picture of the state of the water because the samples have been taken too closely together in time, and
b
so that the results, when considered together, provide information about the water that is representative of the quality of the water during the course of that year.
Monitoring: radioactive substances
6
In the case of samples that a food authority must take and analyse to discharge its obligations under the provisions specified in paragraph 4(2)(c) to (e), the samples must—
a
be taken and analysed by the food authority no less frequently than provided for in the table in Part 3, unless—
i
a decision is taken by the authority under paragraph 27, 33, 42 or 47 to reduce the minimum frequency at which it must take and analyse samples, in which case the authority must take and analyse samples at the reduced minimum frequency decided by it under the relevant paragraph until such time as it takes a different decision relating to the minimum frequency at which relevant samples must be taken and analysed;
ii
a decision is taken by the authority under paragraph 42 or 47 to stop taking and analysing samples, in which case the authority, in accordance with that decision, is not obliged to take and analyse samples until such time as it takes a different decision relating to the minimum frequency at which relevant samples must be taken and analysed;
b
be taken, in so far as possible, so that the number of samples are distributed equally in time and (where appropriate) location.
Microbiological parameters
7
1
A food authority must monitor the value for each of the parameters specified in the first column of the table in Part 2 of Schedule 2 (microbiological parameters) in any water in its area to which this Schedule applies by analysing a sample of the water to determine whether the value for the parameter in the sample exceeds the value specified for the parameter in the second column of the table, as measured by reference to the unit of measurement specified in the third column of the table.
2
For the purpose of the determination required by sub-paragraph (1), the food authority must analyse the sample using the method of analysis for the relevant parameter specified in Part 4.
Chemical parameters
8
1
A food authority must monitor the concentration of each of the parameters specified in the first column of the table in Part 3 of Schedule 2 (chemical parameters) in any water in its area to which this Schedule applies by analysing a sample of the water to determine whether the concentration of the parameter in the sample exceeds the concentration specified for the relevant parameter in the second column of the table—
a
as measured by reference to the unit of measurement specified in the third column of the table, and
b
as read, in the case of a parameter for which there is an entry in the fourth column of the table, with the further provision relating to the parameter or parametric concentration specified in that entry.
2
For the purpose of the determination required by sub-paragraph (1), the food authority must analyse the sample using a method of analysis that complies with Part 5.
3
But sub-paragraph (2) does not apply, and it is not necessary for a food authority to analyse a sample of water under sub-paragraph (1) to determine whether the concentration of acrylamide, epichlorohydrin or vinyl chloride exceeds the concentration specified for that parameter in the second column of the table in Part 3 of Schedule 2, where—
a
the food authority is satisfied that the water, before it is bottled, does not come into contact with a pipe or other construction product that has been constructed using that parameter as a component in its construction, or
b
in other cases, the food authority is satisfied, on the basis of a certificate of conformity, declaration of conformity or declaration of performance relating to a pipe or other construction product that the water comes into contact with, or may come into contact with, before being bottled, and any other related information that it considers to be relevant, that any residual monomer concentration of that parameter in the water does not exceed the concentration for that parameter specified in the second column of the table in Part 3 of Schedule 2.
4
A food authority must not use the uncertainty of measurement percentage specified in the second column of the table in Section 2 of Part 5 (which is concerned with whether a method of analysis complies with minimum performance characteristics) as an additional tolerance when determining whether a parameter specified in the first column of the table in Part 3 of Schedule 2 exceeds the concentration for that parameter specified in the second column of the table in Part 3 of Schedule 2.
5
In sub-paragraph (3)(b)—
“certificate of conformity” means a certificate of conformity issued on or before 30th June 2013—
under the Construction Products Regulations 1991 ; or
under Council Directive 89/106/EEC on the approximation of laws, regulations and administrative provisions of the Member States relating to construction products , as implemented under the law of a member State other than the United Kingdom;
“construction product” has the meaning given in point (1) of Article 2 of Regulation (EU) No 305/2011 of the European Parliament and of the Council laying down harmonised conditions for the marketing of construction products and repealing Council Directive 89/106/EEC ;
“declaration of conformity” means a declaration of conformity issued on or before 30th June 2013—
under the Construction Products Regulations 1991; or
under Council Directive 89/106/EEC , as implemented under the law of a member State other than the United Kingdom;
“declaration of performance” means a declaration of performance drawn up in accordance with Article 4 of Regulation (EU) No 305/2011 of the European Parliament and of the Council.
Radon
9
A food authority must monitor the level of radon in any water in its area to which this Schedule applies in accordance with Part 6.
Tritium
10
A food authority must monitor the level of tritium in any water in its area to which this Schedule applies in accordance with Part 7.
Indicative dose
11
A food authority must monitor the level of the indicative dose for any water in its area to which this Schedule applies in accordance with Part 8.
Indicator parameters
12
A food authority must monitor the concentration or value (as the case may be) of each of the parameters specified in the first column of the table in Section 1 of Part 9 (indicator parameters) in any water in its area to which this Schedule applies in accordance with Part 9.
Other parameters
13
Where a food authority believes, or has reason to suspect, that a property, element, substance or organism that is not specified in any of the tables in Schedule 2 or the table in Section 1 of Part 9, may be present in any water in its area to which this Schedule applies at any concentration, or in any number, that may constitute a potential danger to human health, it must take and analyse samples of the water, on a case by case basis, to determine whether that property, element, substance or organism is present in the water and whether it is present in the water at any concentration, or in any number, that may constitute a potential danger to human health.
Delegation of tasks
14
To enable a food authority to discharge its functions under this Schedule, a food authority may from time to time enter into an arrangement with another person under which the food authority delegates specified tasks to the delegate to carry out on behalf of the food authority on condition that—
a
such arrangement is in accordance with—
i
Part 10, and
ii
Article 5(2) of Regulation 882/2004 (delegation of specific tasks related to official controls), and
b
the food authority notifies the Secretary of State in advance of the proposed delegation and provides the Secretary of State with the information specified in Article 5(4) of Regulation 882/2004.
Quality management practices
15
1
A food authority must not analyse a sample taken for the purpose of carrying out its monitoring obligations under regulation 16A, as read with this Schedule, unless quality management practices that comply with BS EN ISO/IEC 17025:2017 entitled “General requirements for the competence of testing and calibration laboratories” (ISBN 978 0 580 88466 5) published by the BSI on 31st December 2017, or another equivalent standard accepted at international level, are being complied with at the laboratory in which the sample is analysed.
2
But, in the case of the analysis of a sample for the purposes of the monitoring obligations under the provisions specified in sub-paragraph (3), it is sufficient if the laboratory at which the sample is analysed has a system of analytical quality control in place that is checked by the United Kingdom Accreditation Service from time to time.
3
The provisions are those in—
a
paragraph 9, as read with Part 6 (radon),
b
paragraph 10, as read with Part 7 (tritium), and
c
paragraph 11, as read with Part 8 (indicative dose).
Validation and documentation
16
1
A food authority must ensure that any analysis that it carries out for the purpose its monitoring obligations under regulation 16A, as read with this Schedule, is validated and documented in accordance with BS EN ISO/IEC 17025:2017 entitled “General requirements for the competence of testing and calibration laboratories” (ISBN 978 0 580 88466 5) published by the BSI on 31st December 2017 or another equivalent standard accepted at international level.
2
But, in the case of the analysis of a sample for the purpose of the monitoring obligations under the provisions specified in sub-paragraph (3), it is sufficient if the laboratory at which the sample is analysed has a system of analytical quality control in place that is checked by the United Kingdom Accreditation Service from time to time.
3
The provisions are those in—
a
paragraph 9, as read with Part 6 (radon),
b
paragraph 10, as read with Part 7 (tritium), and
c
paragraph 11, as read with Part 8 (indicative dose).
PART 3
Minimum sampling and analyses frequencies for monitoring radioactive substances
Average volume of water bottled each day within a supply zone m 3 Number of samples per year
(1)
The volume of water bottled each day must be calculated as an average taken over a year.
(2)
“a supply zone” means a geographically defined area within which water intended for human consumption comes from one or more sources and within which water quality may be considered as being approximately uniform.
1,000 or less 1 More than 1,000 but less than or equal to 10,000 1 Plus 1 for each 3,300m 3 of the average volume produced each day Plus 1 for any remaining part of the average volume produced each day that is less than 3,300m 3 More than 10,000 but less than or equal to 100,000 3 Plus 1 for each 10,000 m 3 of the average volume produced each day Plus 1 for any remaining part of the average volume produced each day that is less than 10,000 m 3 More than 100,000 10 Plus 1 for each 25,000 m 3 of the average volume produced each day Plus 1 for any remaining part of the average volume produced each day that is less than 25,000 m 3
PART 4
Methods of analyses relating to specified microbiological parameters
Parameter Method of analysis
Escherichia coli (E. coli) BS EN ISO 9308-1:2014+A1:2017 entitled “Water quality — Enumeration of Escherichia coli and coliform bacteria. Part 1: Membrane filtration method for waters with low bacterial background flora (ISO 9308-1:2014)” (ISBN 978 0 580 92379 1) published by the BSI on 31st October 2014, as amended on 28th February 2017, or BS EN ISO 9308-2:2014 entitled “Water quality — Enumeration of Escherichia coli and coliform bacteria. Part 2: Most probable number method” (ISBN 978 0 580 84023 4) published by the BSI on 30th June 2012, as amended by a corrigendum issued on 30th June 2014 Enterococci BS EN ISO 7899-2:2000, BS 6068-4.4:2000 entitled “Water quality — Detection and enumeration of intestinal enterococci — Part 2: Membrane filtration method” (ISBN 0 580 34953 5) published by the BSI on 15th August 2000 Pseudomonas aeruginosa BS EN ISO 16266:2008 entitled “Water quality — Detection and enumeration of Pseudomonas aeruginosa — Method by membrane filtration” (ISBN 978 0 580 59736 7) published by the BSI on 31st March 2008 Colony count 22ºC – enumeration of culturable microorganisms BS EN ISO 6222: 1999, BS 6068-4.5:1999 entitled “Water quality — Enumeration of cultural micro-organisms — Colony count by inoculation in a nutrient agar culture medium” (ISBN 0 580 32495 8) published by the BSI on 15th August 1999 Colony count 36ºC – enumeration of culturable microorganisms BS EN ISO 6222: 1999, BS 6068-4.5:1999 entitled “Water quality — Enumeration of cultural micro-organisms — Colony count by inoculation in a nutrient agar culture medium” (ISBN 0 580 32495 8) published by the BSI on 15th August 1999
PART 5
Methods of analysis relating to chemical parameters
SECTION 1
Methods of analysis
Method of analysis
17
In relation to a parameter specified in the first column of the table in Part 3 of Schedule 2 (chemical parameters)—
a
where there is a method of analysis that meets minimum performance characteristics that can be used by a food authority to analyse a sample for the purpose of making a determination in relation to that parameter under paragraph 8, the food authority must analyse the sample using that method of analysis (or using any one of them in a case where more than one method of analysis meets minimum performance characteristics);
b
where there is no such method of analysis, the food authority must analyse a sample under paragraph 8 using the best available technique not entailing excessive cost.
Minimum performance characteristics
18
1
For the purpose of paragraph 17(a), a method of analysis for a parameter specified in the first column of the table in Section 2 (minimum performance characteristics for a method of analysis) is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—
a
is capable of measuring concentrations equal to the parametric concentration of that parameter with a limit of quantification of 30% or less of the relevant parametric concentration,
b
has an uncertainty of measurement that does not exceed the percentage of the parametric concentration for the parameter specified in the second column of the table,
c
in the case of benzo(a)pyrene, complies, where relevant, with the requirement specified in the third column of the table, and
d
in the case of cyanide, complies with the requirement specified in the fourth column of the table.
2
In the case of a parameter specified in the first column of the table in Section 2, where a method of analysis that complies with the requirements of sub-paragraph (1) is used to determine whether the concentration of that parameter exceeds the concentration specified for that parameter in the table in Part 3 of Schedule 2, the result of the analysis carried out using that method of analysis must be expressed using at least the same number of significant figures as the number of significant figures used to specify that parametric concentration in the table in Part 3 of Schedule 2.
Minimum performance characteristics: individual pesticides
19
1
For the purpose of paragraph 17(a), a method of analysis for an individual pesticide is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—
a
is capable of measuring concentrations equal to the parametric concentration for that pesticide with a limit of quantification of 30% or less of the relevant parametric concentration;
b
has an uncertainty of measurement that does not exceed 30% of the parametric concentration for that pesticide or, where there is no method of analysis for the pesticide that does not exceed 30% of that concentration, an uncertainty of measurement that does not exceed—
i
where there is a method of analysis for the pesticide that has an uncertainty of measurement of more than 30% but less than 80%—
aa
the uncertainty of measurement percentage that applies in relation to that method of analysis, or
bb
where there is more than one such method of analysis for the pesticide, the lowest of those percentages, or
ii
80%, where there is not a method of analysis for the pesticide that has an uncertainty of measurement of less than 80%.
2
Where a method of analysis that complies with the requirements of sub-paragraph (1) is used to determine whether the concentration of an individual pesticide exceeds the parametric concentration specified in the table in Part 3 of Schedule 2 that applies to that pesticide, the result of the analysis carried out using that method of analysis must be expressed using at least the same number of significant figures as the number of significant figures used to specify the parametric concentration that applies to that pesticide in the table.
Alternative minimum performance characteristics
20
1
For the purpose of paragraph 17(a), until the end of 31st December 2019, a method of analysis for a parameter specified in the first column of the table in Section 3 (alternative minimum performance characteristics for a method of analysis that may be used until the end of 31st December 2019) is a method of analysis that complies with minimum performance characteristics if it is a method of analysis that—
a
is capable of measuring parametric concentrations with a trueness not less than the percentage of the parametric concentration specified in the second column of the table,
b
is capable of measuring parametric concentrations with a precision not less than the percentage of the parametric concentration specified in the third column of the table,
c
has a limit of detection that does not exceed the percentage of the parametric concentration specified in fourth column of the table, and
d
in the case of cyanide, complies with the requirement specified in the fifth column of the table.
2
For the purpose of sub-paragraph (1)(b) and the table in Section 3, “precision” (the random error) is twice the relative standard deviation (within a batch and between batches) of the spread of results from the mean as further described in ISO 5725-1:1994(en) entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions” published by the International Organization for Standardization on 22nd December 1994, as amended by ISO 5725-1:1994/Cor 1:1998 entitled “Accuracy (trueness and precision) of measurement methods and results – Part 1: General principles and definitions TECHNICAL CORRIGENDUM 1” published by the International Organization for Standardization on 2nd May 1998.
3
For the purpose of subparagraph (1)(c) and the table in Section 3, the limit of detection is—
a
three times the standard deviation within a batch of a natural sample containing a low concentration of the parameter, or
b
five times the standard deviation of a blank sample within a batch.
Uncertainty of measurement
21
1
For the purpose of paragraph 18(1)(b) and 19(1)(b), the performance criterion for uncertainty of measurement (k = 2) for a parameter specified in the first column of the table in Section 2 is not less than the percentage specified in the second column of the table of the concentration for the parameter specified in the second column of the table in Part 3 of Schedule 2.
2
Food authorities must estimate uncertainty of measurement for a parameter specified in the first column of the table in Section 2 at the level of the concentration for the parameter specified in the second column of the table in Part 3 of Schedule 2.
SECTION 2
Minimum performance characteristics for a method of analysis
Parameters Uncertainty of measurement - percentage of the parametric concentration Other requirements relating to the uncertainty of measurement Other requirements
Antimony 40 Arsenic 30 Benzene 40 Benzo(a)pyrene 50 Where there is no method of analysis for benzo(a)pyrene that has an uncertainty of measurement that does not exceed 50%, the best available method of analysis with an uncertainty of measurement not exceeding 60% must be used. Boron 25 Bromate 40 Cadmium 25 Chromium 30 Copper 25 Cyanide 30 The method of analysis must determine total cyanide in all forms. 1,2-dichloroethane 40 Fluoride 20 Lead 25 Mercury 30 Nickel 25 Nitrate 15 Nitrite 20 Polycyclic aromatic hydrocarbons— (a) individual substance 25 (b) total substances 50 Selenium 40 Tetrachloroethenes— (a) individual substance 50 (b) total substances 30 Trichloroethenes— (a) individual substance 50 (b) total substances 40 Trihalomethanes— (a) individual substance 25 (b) total substances 40
SECTION 3
Alternative minimum performance characteristics for a method of analysis that may be used until the end of 31st December 2019
Parameters Trueness - percentage of the parametric concentration Precision -percentage of the parametric concentration Limit of detection -percentage of the parametric concentration Other requirements
Antimony 25 25 25 Arsenic 10 10 10 Benzene 25 25 25 Benzo(a)pyrene 25 25 25 Boron 10 10 10 Bromate 25 25 25 Cadmium 10 10 10 Chromium 10 10 10 Copper 10 10 10 Cyanide 10 10 10 The method of analysis must determine total cyanide in all forms. 1,2-dichloroethane 25 25 10 Fluoride 10 10 10 Lead 10 10 10 Mercury 20 10 20 Nickel 10 10 10 Nitrate 10 10 10 Nitrite 10 10 10 Pesticide – individual substance 25 25 25 Polycyclic aromatic hydrocarbons— (a) individual substance 25 25 25 (b) total substances 25 25 25 Selenium 10 10 10 Tetrachloroethenes— (a) individual substance 50 50 50 (b) total substances 25 25 10 Trichloroethenes— (a) individual substance 50 50 50 (b) total substances 25 25 10 Trihalomethanes— (a) individual substance 25 25 25 (b) total substances 25 25 10
PART 6
Monitoring obligations relating to radon
Representative surveys
22
1
Each food authority must undertake representative surveys to determine the scale and nature of likely exposure to radon originating from different types of groundwater sources and wells in different geological areas within its area.
2
The representative surveys must be designed in such a way that underlying parameters determining the likely exposure to radon, including the geology and hydrology of the area, the radioactivity of the rock types and soil types within the area and the type of wells within the area, can be identified and used to determine whether any source or well within the food authority’s area is in an area of likely high exposure to radon.
Monitoring obligation
23
Each food authority must monitor the concentration of radon in any water in its area to which this Schedule applies unless an exemption from monitoring under paragraph 24 is in force.
Exemption
24
1
A food authority is not required to monitor the concentration of radon in any water in its area if—
a
on the basis of an assessment of representative surveys, monitoring data and such other information that it considers to be reliable, it is satisfied that the activity concentration of radon in the water does not exceed 100 Bq/l and has decided that it is unlikely to do so for at least five years beginning with the day after the day on which it comes to that decision (“assessment decision”),
b
it notifies the Secretary of State of its assessment decision and provides the Secretary of State with a copy of the representative surveys, monitoring data and any other information that the authority took into account in coming to that decision,
c
it notifies the Secretary of State that, on the basis of its assessment decision, the authority has decided not to monitor the activity concentration of radon in the water for a period of five years beginning with the day after the day on which the notification is submitted to the Secretary of State, and
d
in a case where sub-paragraph (2) applies, the food authority is satisfied that the activity concentration of radon in the water is unlikely to exceed 100 Bq/l for a period of five years beginning with the day after the day on which the food authority submits the notification under paragraph (c).
2
This sub-paragraph applies where a notification under sub-paragraph (1)(c) is submitted more than three months after the day after the day on which a food authority makes an assessment decision under sub-paragraph (1)(a).
3
A notification submitted by a food authority under sub-paragraph (1) may relate to all or some of the water in its area to which this Schedule applies.
4
The exemption from monitoring provided for in sub-paragraph (1) lapses after a period of five years beginning with the day after the day on which the food authority submits the notification referred to in sub-paragraph (1)(c).
5
But the exemption lapses immediately if the food authority becomes aware (by whatever means) at any time during the five year exemption period that the activity concentration of radon in the water exceeds 100 Bq/l or it has reason to suspect that the activity concentration of radon in the water may exceed 100 Bq/l.
Analysis of sample
25
1
Where it is necessary under paragraph 23 for a food authority to monitor any water in its area to which this Schedule applies, the food authority must analyse a sample of the water to determine whether the activity concentration of radon in the water in that sample exceeds 100 Bq/l.
2
The food authority must analyse the sample using a method of analysis that is capable of measuring the activity concentration of radon in the water with a level of detection not exceeding 10 Bq/l.
3
The limit of detection for a method of analysis relating to the activity concentration of radon must be calculated in accordance with ISO Standard ISO 11929:2010(en) entitled “Determination of the characteristic limits (decision threshold, detection limit and limits of the confidence interval) for measurements of ionizing radiation - Fundamentals and application” published by the International Organization for Standardization on 24th February 2010, with probabilities of errors of the first and second kind of 0.05 each.
4
In relation to the limit of detection, the uncertainty of measurement must be calculated and reported as complete standard uncertainties, or as expanded standard uncertainties with an expansion factor of 1.96, in accordance with ISO/IEC Guide 98-3:2008 (JCGM/WG1/100) entitled “Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)” published by the International Organization for Standardization on 30th September 2008, as amended by—
a
ISO/IEC Guide 98-3:2008/Suppl 1:2008 (JCGM/WG1/101) entitled “Propagation of distributions using a Monte Carlo method” published by the International Organization for Standardization on 20th November 2010, and
b
ISO/IEC Guide 98-3:2008/Suppl 2:2011 (JCGM/WG1/102) entitled “Extension to any number of output quantities” published by the International Organization for Standardization on 9th November 2011.
Action following the result of analysis
26
1
This paragraph applies if the result of an analysis of a sample of water carried out by a food authority under paragraph 25, or under any other provision of this Schedule, detects an activity concentration of radon exceeding 100 Bq/l.
2
If an activity concentration of radon exceeding 1,000 Bq/l is detected in a sample of water, the food authority must take action under paragraph 57 (remedial action).
3
If an activity concentration of radon exceeding 100 Bq/l but not exceeding 1,000 Bq/l is detected in a sample of water (“Sample X”), the food authority must—
a
take and analyse an extra sample of the water as soon as reasonably practicable after the result of Sample X is detected to determine the activity concentration of radon in the extra sample;
b
if the food authority considers it appropriate to do so, continue taking and analysing extra samples of the water to determine the activity concentration of radon in those samples at such intervals and for such period as the food authority, taking into account the provisions of sub-paragraphs (4) to (6), considers appropriate.
4
The food authority must, disregarding the result of Sample X, determine the average of the activity concentration of radon in the water for such 12 month period as the authority considers appropriate (whether the 12 month period used by the food authority for the purpose of its monitoring programme or some other 12 month period) on the basis of—
a
the results of the analyses of samples of the water carried out before the determination of the result of Sample X,
b
the result of the analysis of the extra sample under sub-paragraph (3)(a), and
c
where extra samples are taken under sub-paragraph (3)(b), the results of the analyses of those extra samples.
5
No further action by the food authority is required if the outcome of the determination under sub-paragraph (4) is that the average of the activity concentration of radon in the water for the relevant 12 month period does not exceed 100 Bq/l.
6
The food authority must take action under paragraph 57(1) (remedial action) if the outcome of the determination under sub-paragraph (4) is that the average of the activity concentration of radon in the water for the relevant 12 month period exceeds 100 Bq/l.
7
Sub-paragraphs (3) to (6) do not apply if the food authority is of the opinion that—
a
even if it took extra samples under sub-paragraph (3) to enable it to determine the activity concentration of radon in those extra samples, it would have insufficient results from previous determinations relating to the activity concentration of radon in the water to enable it to make the determination required by sub-paragraph (4) within such period as the food authority considers to be reasonable, or
b
for some other reason, the result of such a determination under sub-paragraph (4), based on the results of those extra samples and previous determinations, may give a distorted result.
8
Where an activity concentration of radon exceeding 100 Bq/l but not exceeding 1,000 Bq/l is detected in a sample of water and, by virtue of sub-paragraph (7), sub-paragraphs (3) to (6) do not apply, a food authority must take action under paragraph 57(1).
Taking of samples: reduced frequency
27
1
A food authority may, from time to time, decide to reduce the frequency at which it takes and analyses samples of any water in its area under paragraph 25 to determine the activity concentration of radon in the water where—
a
the result of the analysis of the last sample of the water carried out by the food authority shows that the activity concentration of radon in the water does not exceed 100 Bq/l,
b
that result, taken together with the results of such other analyses of the water previously carried out by the food authority as it considers relevant to its decision, show that the activity concentration of radon in the water is stable, and
c
the authority is satisfied that the change in the monitoring arrangements will not increase any risk to human health.
2
A food authority that has made a decision under sub-paragraph (1) to reduce the frequency at which it takes samples of any water, may decide at any time to start taking samples of the water again at the frequency provided for in the table in Part 3 or, in accordance with sub-paragraph (1), at some other reduced frequency.
Treated bottled drinking water
28
The provisions of this Part, except for paragraph 27, apply to bottled drinking water that has been treated to reduce the level of radionuclides in the water in the same way as it applies to water that has not been treated in that way.
PART 7
Monitoring obligations relating to tritium
Monitoring obligation
29
Each food authority must monitor the activity concentration of tritium in any water in its area to which this Schedule applies if an anthropogenic source of tritium or other artificial radionuclide is present within the catchment area, unless an exemption from monitoring under paragraph 30 is in force.
Exemption
30
1
A food authority is not required to monitor the activity concentration of tritium in any water in its area if—
a
on the basis of an assessment of representative surveys, monitoring data and such other information as it considers to be reliable, it is satisfied that the activity concentration of tritium in the water does not exceed 100 Bq/l and has decided that it is unlikely to do so for at least five years beginning with the day after the day on which it comes to that decision (“assessment decision”),
b
it notifies the Secretary of State of its assessment decision and provides the Secretary of State with a copy of the representative surveys, monitoring data and any other information that the authority took into account in coming to that decision,
c
it notifies the Secretary of State that, on the basis of its assessment decision, the authority has decided not to monitor the activity concentration of tritium in the water for a period of five years beginning with the day after the day on which the notification is submitted to the Secretary of State, and
d
in a case where sub-paragraph (2) applies, the food authority is satisfied that the activity concentration of tritium in the water is unlikely to exceed 100 Bq/l for a period of five years beginning with the day after the day on which the food authority submits the notification under paragraph (c) to the Secretary of State.
2
This sub-paragraph applies where a notification under sub-paragraph (1)(c) is submitted more than three months after the day after the day on which a food authority makes an assessment decision under sub-paragraph (1)(a).
3
A notification submitted by a food authority under sub-paragraph (1) may relate to all or some of the water in its area to which this Schedule applies.
4
The exemption from monitoring provided for in sub-paragraph (1) lapses after a period of five years beginning with the day after the day on which the food authority submits the notification referred to in sub-paragraph (1)(c).
5
But the exemption lapses immediately if the food authority becomes aware (by whatever means) at any time during the five year exemption period that the activity concentration of tritium in the water exceeds 100 Bq/l or it has reason to suspect that the activity concentration of tritium in the water may exceed 100 Bq/l.
Analysis of sample
31
1
Where it is necessary under paragraph 29 for a food authority to monitor any water in its area to which this Schedule applies, the food authority must analyse a sample of the water to determine whether the activity concentration of tritium exceeds 100 Bq/l.
2
The food authority must analyse the sample using a method of analysis that is capable of measuring the activity concentration of tritium in the water with a level of detection not exceeding 10 Bq/l.
3
The provisions in paragraph 25(3) and (4) (relating to the calculation and reporting of the limit of detection) apply in the same way to the calculation of the limit of detection for a method of analysis used to measure the activity concentration of tritium as they apply to the calculation and reporting of the limit of detection for a method of analysis used to measure the activity concentration of radon.
Action following the results of analysis
32
1
This paragraph applies if the result of an analysis of a sample of any water carried out by a food authority under paragraph 31, or under any other provision of this Schedule, detects an activity concentration of tritium exceeding 100 Bq/l in that sample (“Sample X”).
2
The food authority must—
a
take and analyse an extra sample of the water as soon as reasonably practicable after the result of Sample X is detected by it to determine the activity concentration of tritium in the extra sample,
b
if the food authority considers it appropriate to do so, continue taking and analysing extra samples of the water to determine the activity concentration of tritium in those samples at such intervals and for such period as the food authority, taking into account sub-paragraphs (3) to (5), considers appropriate,
c
determine, by analysis, the gross alpha activity and gross beta activity of the water using water from the same sample, and
d
taking into account such information about likely sources of radioactivity affecting the water as the food authority considers relevant, analyse a sample of the water (whether water from the same sample or from a different sample of the water) to determine whether such other artificial radionuclides as the food authority may consider relevant are present in the water.
3
The food authority must, disregarding the result of Sample X, determine the average of the activity concentration of tritium in the water for such 12 month period as the authority considers appropriate (whether the 12 month period used by the food authority for the purpose of its monitoring programme or some other 12 month period) on the basis of—
a
the results of the analyses of samples of the water carried out before the determination of the result of Sample X,
b
the result of the analysis of the extra sample under sub-paragraph (2)(a), and
c
where extra samples are under sub-paragraph (2)(b), the results of the analyses of those extra samples.
4
No further action by the food authority is required if the outcome of the determination under sub-paragraph (3) is that the average of the activity concentration of tritium in the water for the relevant 12 month period does not exceed 100 Bq/l.
5
The food authority must take action under paragraph 57(1) (remedial action) if the outcome of the determination under sub-paragraph (3) is that the average of the activity concentration of tritium in the water for the relevant 12 month period exceeds 100 Bq/l.
6
Sub-paragraphs (2)(a) and (b) and (3) to (5) do not apply if the food authority is of the opinion that—
a
even if it took extra samples under sub-paragraph (2)(a) and (b) to enable it to determine the activity concentration of tritium in those extra samples, it would have insufficient results from previous determinations relating to the activity concentration of tritium in the water to enable it to make the determination required by sub-paragraph (3) within such period as the food authority considers to be reasonable, or
b
for some other reason, the result of such a determination under sub-paragraph (3) based on the results of those extra samples and previous determinations may give a distorted result.
7
Where an activity concentration of tritium exceeding 100 Bq/l is detected in a sample of water and, by virtue of sub-paragraph (6), sub-paragraphs (2)(a) and (b) and (3) to (5) do not apply, the food authority must take action under paragraph 57(1).
8
Where a determination of the gross alpha activity and gross beta activity must be made by a food authority under sub-paragraph (2)(c), the food authority must apply the provisions of paragraph 38(2) to (8), in the case of gross alpha activity, and paragraph 39(2) to (8), in the case of gross beta activity, in carrying out that determination and deciding what further action, if any, to take.
Taking of samples: reduced frequency
33
1
A food authority may, from time to time, decide to reduce the frequency at which it takes and analyses samples of any water in its area under paragraph 31 to determine the activity concentration of tritium in the water where—
a
the result of the analysis of the last sample of the water carried out by the food authority shows that the activity concentration of tritium in the water does not exceed 100 Bq/l,
b
that result, taken together with the results of such other analyses of the water previously carried out by the food authority as it considers relevant to its decision, show that the activity concentration of tritium in the water is stable, and
c
the authority is satisfied that the change in the monitoring arrangements will not increase any risk to human health.
2
A food authority which has made a decision under sub-paragraph (1) to reduce the frequency at which it takes samples of water, may decide at any time to start taking samples of the water again at the frequency provided for in the table in Part 3 or, in accordance with sub-paragraph (1), at some other reduced frequency.
Treated bottled drinking water
34
The provisions of this Part, except for paragraph 33, apply to bottled drinking water that has been treated to reduce the level of radionuclides in the water in the same way as it applies to water that has not been treated in that way.
PART 8
Monitoring obligations relating to indicative dose
SECTION 1
General
Monitoring obligation
35
If a source of artificial or elevated natural radioactivity is present in a food authority’s area, it must monitor the indicative dose for any water in its area to which this Schedule applies unless an exemption
The text continues in the official source.
